Hi, I'm Tom. Welcome to our shop,
Carymart offers you the premium rf remote control equipment.
We suggest you reading our FAQs before making your decision.
If you have any other question, please contact us.
We will reply you as soon as possible.
Application:
Mainly used for doors, windows, cellars, trapdoors, hatchways, solar
tracking system, medical devices, agricultural machinery, vehicles, ships,
elevator platforms, lifting tables, TV lifts, robots, cabinetries, massage
sofas, electric beds, medical chairs, and other electrical equipment. It can
open, close, push, pull, lift, and descend these devices.
It can replace hydraulic and pneumatic products to save power consumption.
Feature:
High-quality products and high-quality services
Metal housing, able to work in very harsh environments
Metal gearbox and high strength wear-resistant metal gears
Stainless steel telescopic tube and outer tube, good corrosion resistant
Heavy duty design, high-power DC motor
Strong thrust, up to 8000N / 800 Kgs / 1800 lbs
Multiple speed options, from 5 mm/second to 50 mm/second
Multiple stroke options, from 10 mm to 650 mm
We can customize any stroke length from 10mm to 650mm, such as 180mm, 480mm,
650mm and so on.
Advanced waterproof and dustproof technology
Low power consumption and low noise
Built-in clutch to protect gears and motors
Built-in motor overload and overheat protection
Built-in two limit switches, linear actuator will automatically stop when
stroke rod reaches the limit position.
Built-in Hall sensor is optional, so you can use the synchronous controller
to operate 2 linear actuators fully synchronously.
Automatically lock after stopping, and no power supply is required.
Maintenance-free
Specifications:
Optional working voltage: DC 12V, DC 24V, DC 36V or DC 48V, and 24V is the
most commonly used working voltage.
Stroke range: 0.4 ~ 26 inches or 10 ~ 650 mm (If you want to view detailed information of linear actuators with different
strokes, such as detailed drawings and dimensional drawings, please click
the following link to view:
Linear Actuator C)
Optional speed: 5±1mm/s, 8±2mm/s, 10±2mm/s, 12±2mm/s, 16±3mm/s, 20±4mm/s,
28±6mm/s, 50±10mm/s
The above is the speed at no load, and the actual working speed will
gradually slow down as the load increases.
Max Load capacity: 8000N / 800 Kgs / 1800 lbs at 5mm/s
Linear actuator can get maximum load capacity when it operates in the
vertical direction, and the pulling force is less than pushing force.
No-load current: 2~3A at 12V or 1~1.5A at 24V
Full load current: 12~20A at 12V or 6~10A at 24V
Please use a 12V/50A or 24V/25A power supply to power the two linear
actuators.
Shaft diameter: 28mm
Mounting holes diameter: 13mm [0.512 in]
Housing Material: Stainless steel
Stroke Rod Material: Stainless steel
Gear Material: Steel Alloy
Motor Type: Brushed DC Motor
The orientation of the front and rear connector is default, we can rotate it
90 degrees during the production according to the customer's needs.
Duty cycle: 10%, max 5mins continuous use
Service life: approx. 35, 000 cycles
Power cable: Six-core Wire
Cable length: 600±10%mm [24 in], the length
can also be customized according to your specific needs.
Certifications: CE
Environment temperature: -26℃ to 85℃
Operating Noise: about 56dB~66dB (Linear actuators with different parameters
will have different noise levels.)
IP rating: IP65
Different speeds and corresponding maximum thrust:
No-load Speed
Full load Speed
Maximum Thrust
Self-locking Force
5mm/s
3.5mm/s
8000N / 800 kg / 1800 lbs
8500N / 850 kg / 1900 lbs
8mm/s
6mm/s
7000N / 700 kg / 1600 lbs
7500N / 750 kg / 1700 lbs
10mm/s
7mm/s
6000N / 600 kg / 1300 lbs
6500N / 650 kg / 1500 lbs
12mm/s
9mm/s
5000N / 500 kg / 1100 lbs
5500N / 550 kg / 1200 lbs
16mm/s
12mm/s
4000N / 400 kg / 880 lbs
4500N / 450 kg / 1000 lbs
20mm/s
15mm/s
3000N / 300 kg / 670 lbs
3500N / 350 kg / 790 lbs
28mm/s
20mm/s
2000N / 200 kg / 450 lbs
2500N / 250 kg / 560 lbs
50mm/s
38mm/s
1000N / 100 kg / 200 lbs
1500N / 150 kg / 340 lbs
Note:
1. The above data is the maximum load capacity that can be obtained when
each linear actuator runs in the vertical direction. The maximum load capacity
of the entire synchronous system is the sum of the maximum load capacities of
the three linear actuators. If the weight of your equipment (such as a cellar
door) is 100kg, and you want to use a linear actuator to open this door, you
need to calculate the actual force acting on the linear actuator according to
your installation method. This force is usually 2-5 times the weight of the
cellar door. If you don't know how to calculate it, please contact us for help.
2. The above is the speed at no load, and the actual working speed will
gradually slow down as the load increases. Full load speed is approximately
60-70% of No-load speed.
3. Different speeds correspond to different maximum loads. Please select the
right speed according to the speed and maximum load you need.
4. Linear actuators are not recommended for continuous operation under maximum
load, we recommend letting it work at about half of the maximum load to get a
longer working life.
5. For linear actuators with a stroke greater than 500MM, you should not
normally allow them to operate at their maximum stroke under heavy loads. If the
actual stroke you want is 600MM, we recommend that you choose a linear actuator
with a stroke of 700-800MM.
6. The maximum pull force of the linear actuator is slightly less than its
maximum thrust force.
The information for synchronous controller:
Introduction:
If you want to use multiple linear actuators to raise and lower an
equipment, for example two, three or four electric actuators. Since the
high-speed DC motors in electric actuators cannot run at exactly the same
speed, so the movement speed of the electric actuator will also be
different. When multiple electric actuators work at the same time, their
actual speeds cannot be exactly the same. In this case, we can use a
synchronous controller to operate multiple linear actuators to rise or fall
synchronously. They work completely in sync without any difference.
Working principle:
If you want to use a synchronization controller to operate 2, 3 or 4 linear
actuators fully synchronously, you will need to add built-in Hall effect
sensors for each linear actuator. And when you have purchased Hall effect
sensors along with linear actuators, we will install Hall effect sensors in
the linear actuators during production for you. When 2, 3 or 4 linear
actuators are running together, Hall sensor will send Hall signals to the
synchronization controller, and the controller will adjust the running speed
of each linear actuator, so that all linear actuators run at the exact same
speed.
Feature:
It can operate two electric linear actuators C
to run completely
synchronously.
Wired control via a control handle.
Wireless control via a remote.
Two selectable control modes: Interlocking mode or Momentary Mode.
Two function buttons: Up Down.
With limit control terminals: You can connect external limit switches to
stop linear actuators.
With reset button.
When linear actuators move close to the end position, they will
automatically slow down to protect themselves.
When linear actuators are fully retracted, they will retain 1MM of travel to
protect themselves.
Parameters:
Working Voltage: 12V DC or 24V DC optional, suitable for 12V or 24V linear
actuator
Working Frequency: 433.92 MHz
Working Distance: 100m / 300ft (theoretically)
Rated current: 30A at 12V or 20A at 24V
Two selectable control modes: Interlocking mode or Momentary mode.
Operating Temperature: -20°C ~ +70°C
Case size: 240 x 170 x 56 mm (9.5 x 6.7 x 2.2 inches) Cable length of the control handle: 1500±10%mm [60 in]
Connection:
1) Connect the positive pole of DC power supply to terminal + of the
controller, and connect the negative pole of DC power supply to terminal -
of the controller.
2) Connect red power cable and black power cable of two linear actuators to
linear actuator terminals of the controller.
Caution: When operating the linear actuators by the control handle or
remote, if the working direction of the linear actuators do not correspond
to the direction of the button, please exchange the connection terminals of
two power cables of the linear actuators.
3) Connect four hall signal cables of two linear actuators to hall signal
terminals of the controller.
How to set the control mode:
The controller has two selectable control modes, interlocking mode and
momentary mode. You can switch the control modes as follows:
Simultaneously press and hold the reset button on the controller and the
button UP on the control handle or remote control for 8-9 seconds.
Operation in different control modes:
1. Interlocking control Mode:
1.1 Operation via the control handle:
1) Press the UP button of the control handle, two linear actuators extend
outward at the same time, they will reach the maximum stroke at the same
time and stop automatically. During operation, you can also press any button
of the control handle to stop two linear actuators at the same time.
2) Press the DOWN button of the control handle, two linear actuators retract
inward at the same time, they will fully retract at the same time and stop
automatically. During operation, you can also press any button of the
control handle to stop two linear actuators at the same time.
1.2 Operation via the remote control:
1) Press the button ▲ of the remote control, two linear actuators extend out
at the same time, they will reach the maximum stroke at the same time and
stop automatically. During operation, you can also press any button you can
also press any button of the remote control to stop two linear actuators at
the same time.
2) Press the button ▼ of the remote control, two linear actuators retract
inward at the same time, they will fully retract at the same time and stop
automatically. During operation, you can also press any button of the remote
control to stop two linear actuators at the same time.
2. Momentary Control Mode:
2.1 Operation via the control handle:
1) Press and hold the UP button of the control handle, two linear actuators
extend outward at the same time; Release the button, two linear actuators
stop at the same time.
2) Press and hold the DOWN button of the control handle, two linear
actuators retract inward at the same time; Release the button, two linear
actuators stop at the same time.
2.2 Operation via the remote control:
1) Press and hold the button ▲ of the remote control, two linear actuators
extend out at the same time; Release the button, two linear actuators stop
at the same time.
2) Press and hold the button ▼ of the remote control, two linear actuators
retract inward at the same time; Release the button, two linear actuators
stop at the same time.
Limit control terminals:
The controller has limit control terminals, and you can connect two external
limit switches (with normally open contact) to limit terminals, then use it
to stop two linear actuators.
For example, you can connect a normally open limit switch to terminals UP
and GND, and connect another normally open limit switch to terminals
DOWN and GND.
When two linear actuators extend outward, if the limit switch is triggered,
it will connect two terminals UP and GND, then two linear actuators will
stop automatically.
When two linear actuators inward retract, if the limit switch is triggered,
it will connect two terminals DOWN and GND, then two linear actuators
will stop automatically.
Reset Function:
When this system has been running for a long time, if you find that they are
no longer fully synchronized, you can use the reset button to reset the
controller. Note: Before the reset operation, you need to disconnect the the
connection wires from the two external limit switches to the controller.
Operation: Press and hold the buttons UP and DOWN on the control handle or
remote control at the same time for 5-6 seconds, then release the buttons
and the system will start to reset: two linear actuators will be fully
retracted from their current position, then stretch outward a little, and
finally fully retracted again.
Working status and LED indicators:
1. Power on is normal: The green light is on, and the red light is off.
2. Normal work: The green light is on, the red light is on, and the red
light is off after the work is over.
3. Overload: The green light is on, and the red light is on. At this time,
it cannot work normally, and it must be reset first.
4. The error is too large: The green light is flashing, and the red light is
off. At this time, it cannot work normally, and it must be reset first.
5. Low voltage: The green light is off, and the red light is off.
6. Hall sensor failure: The green light flashes, and the red light is off.
7. During the reset operation: The green light flashes, and the red light
flashes. When the reset is completed, the green light is on, and the red
light is off.
Note:
1. Each linear actuator would require two mounting brackets, one to fix the
head of linear actuator and another to fix the bottom of linear actuator.
This kit does not contain fixed mounting brackets, please buy them from the
drop down menu.
2. You need to use a DC12V/50A or DC24V/25A switching power supply to power
this kit. This kit does not contain this power supply, please buy it from
the drop down menu.
Production time:
The linear actuators are the customized products, and these products are not
in stock, we need to spend 3~7 working days to produce them according to the
specified parameters in your order.
Return or Exchange:
The Linear Actuators are the customized products, we need to produce them
according to the specified parameters in your order, so that we do not accept
returns or cancel orders. If customers order unsuitable linear actuators
themselves, we also do not accept exchanges, please understand.
We can provide 3D CAD model files in STEP format for linear actuators.
Please contact us by e-mail if you need them.
Package Include:
2 x Electric Linear Actuator C With Hall Effect Sensor
1 x Synchronous Controller (One-Control-Two, For 2 Linear Actuator C)
1 x Control Handle
1 x Remote Control (CP-2)
1 x User manual Note: The
synchronous controller has two control modes, interlocking mode and
momentary mode, please select a control mode you need when ordering.
