Hi, I'm Tom. Welcome to our shop,
Carymart offers you the premium rf remote control equipment.
We suggest you reading our FAQs before making your decision.
If you have any other question, please contact us.
We will reply you as soon as possible.
Package Include:
1 x Receiver: S6CA-DC-ANT3
1 x User manual
Application:
This receiver is an electric device with 6 dry relay outputs, it and the
transmitter form a wireless remote-control system. This system may be used
in all types of industry automation, agriculture, business, home, factory,
house, farm, garage, vehicle, ship, aerial vehicle, etc. It can remote
control different AC or DC equipment on land, water, and air, such as
lights, doors, windows, lamps, sockets, locks, sirens, outlets, heaters,
motors, fans, winches, curtains, blinds, linear actuators, electric solenoid
valves, and security alarm systems. The applications are endless.
Feature:
Wireless control, easy to install.
Four operating voltage versions: DC 6V, 9V, 12V, 24V optional.
Relay Output: This receiver is dry relay output; it can be used to operate
both DC and AC equipment. The output terminals are NO / NC (normally open /
normally closed), serving as a switch.
With external antenna, the receiver has a farther working range.
The transmitter / remote can control the receiver from any place within a
reliable working distance.
Wireless RF signal from the transmitter can pass through walls, floors,
doors, or windows, but it will lose some operating range.
The receiver has reverse voltage protection and overcurrent protection.
The receiver can only be triggered by paired transmitters.
One or more transmitters / remotes can control one or several receivers
simultaneously.
Two or more receivers may be used in the same area.
Receiver Parameters:
Model: S6CA-DC-ANT3
Operating Voltage: 6VDC (model S6CA-DC06), or 9±1VDC (model S6CA-DC09), or
12±1VDC (model S6CA-DC12), or 24±2VDC (model S6CA-DC24), the operating
voltage must be specified when ordering.
Working Frequency: 433.92 MHz
Quiescent Current: ≤10mA
Channel: 6 CH
Output Type: Dry Relays Output (With Normally Open and Normally Closed
Terminals)
Maximum Load Voltage of Relay: 240VAC or 28VDC
Maximum Load Current of Relay: 10A / channel
Suitable Wires for Connecting Terminals: 22-12 AWG
6 Selectable Working Modes: Self-locking, Momentary, Interlocking,
Self-locking + Momentary, Momentary + Interlocking
Operating Temperature: -20 °C ~ +70 °C
PCB size: 75 x 58 x 16 mm (3.0 x 2.3 x 0.6 inches)
Case size: 95 x 62 x 28 mm (3.7 x 2.4 x 1.1 inches)
Matching Transmitters:
This receiver only works with the transmitters
CD-6
.
Working Range:
The receiver and the transmitter CD-6 form a complete kit, the maximum
working distance may reach 3000 feet or 1000 meters in an open area.
The maximum working distance is a theoretical data, it shall be operated in
an open ground, no barriers, no interference. But in the practice, it will
be hindered by trees, walls, or other construction, and will be interfered
by other wireless signals. Therefore, the actual working distance may not
reach this maximum distance.
Usage:
The receiver can be used to control both 0~28VDC and 110~240VAC devices.
Notice: The receiver is dry relay output, not DC/AC power output. Initial
state of relay output terminals: Terminals and are Normally Open;
Terminals and are Normally Closed.
Wiring:
1) If you want to control a DC 12V lamp, do as following:
1.1 Connect the positive pole of DC power supply to terminal , and
connect the negative pole of DC power supply to terminal .
1.2 Connect terminal to the positive pole of DC power supply, connect
terminal to the positive pole of DC lamp, and connect the negative
pole of DC lamp to the negative pole of DC power supply.
2) If you want to control an AC 220V lamp, do as following:
2.1 Connect the positive pole of DC power supply to terminal , and
connect the negative pole of DC power supply to terminal .
2.2 Connect terminal to the live wire of AC power supply, connect
terminal to one side of AC lamp, and connect another side of AC lamp
to the neutral wire of AC power supply.
Setting different working modes:
The receiver will be set in Self-locking mode before leaving the factory, if
you want to use another mode, please follow the following steps.
1) Setting Self-locking mode: When the receiver is in the learning status,
press the button 1 on the transmitter.
The operation of Self-locking mode with the transmitter CD-6:
Press the button 1 on the transmitter: The relay 1 in the receiver is
activated, and the connected lamp 1 is turned on.
Press the button 1 again: The relay 1 is deactivated, and the connected lamp
1 is turned off.
............
Press the button 6 on the transmitter: The relay 6 in the receiver is
activated, and the connected lamp 6 is turned on.
Press the button 6 again: The relay 6 is deactivated, and the connected lamp
6 is turned off.
2) Setting Momentary mode: When the receiver is in the learning status,
press the button 2 on the transmitter.
The operation of Momentary mode with the transmitter CD-6:
Press and hold the button 1 on the transmitter: The relay 1 in the receiver
is activated, and the connected lamp 1 is turned on.
Release the button 1: The relay 1 is deactivated, and the connected lamp 1
is turned off.
............
Press and hold the button 6 on the transmitter: The relay 6 in the receiver
is activated, and the connected lamp 6 is turned on.
Release the button 6: The relay 6 is deactivated, and the connected lamp 6
is turned off.
3) Setting Interlocking mode: When the receiver is in the learning status,
press the button 3 on the transmitter.
The operation of Interlocking mode with the transmitter CD-6:
Press the button 1 on the transmitter: The relay 1 in the receiver is
activated, and the connected lamp 1 is turned on. Other 5 relays are
deactivated and other 5 connected lamps are turned off.
............
Press the button 6 on the transmitter: The relay 6 in the receiver is
activated, and the connected lamp 6 is turned on. Other 5 relays are
deactivated and other 5 connected lamps are turned off.
4) Setting Self-locking (Channels 1~3) + Momentary (Channels 4~6) mode: When
the receiver is in the learning status, press the button 4 on the
transmitter.
5) Setting Self-locking (Channel 1) + Momentary (Channels 2~6) mode: When
the receiver is in the learning status, press the button 5 on the
transmitter.
The operation with the transmitter CD-6:
6) Setting Momentary (Channels 1~2) + Interlocking (Channels 3~6) mode: When
the receiver is in the learning status, press the button 6 on the
transmitter.
How to pair the transmitter to the receiver:
Notice: We have paired the transmitter to the receiver before leaving the
factory.
1) Press the learning button in the receiver and the signal LED on the
receiver turns on first and then goes off, this indicates that the receiver
enters the learning status.
2) Press the corresponding button on the transmitter according to the
working mode you need, if signal LED flashes 3 times, this indicates that
the pairing is successful.
3) The receiver can learn 30 transmitters with different codes.
How to delete all transmitters codes stored in the receiver:
We have paired the transmitter to the receiver, if you don’t want the
receiver to work with the transmitter, you can delete all transmitters codes
stored in the receiver.
Operation: Press and hold the learning button in the receiver for 10
seconds, the signal LED on the receiver stays on for about 10 seconds and
then goes off, then release the learning button, this indicates that all
stored codes have been deleted successfully.
