Hi, I'm Tom. Welcome to our shop,
Carymart offers you the premium rf remote control equipment.
We suggest you reading our FAQs before making your decision.
If you have any other question, please contact us.
We will reply you as soon as possible.
Feature: Application:
It can be used in industry automation, agriculture automation and home
automation, such as factory, house, farm, pasture, vehicle, ship, offshore
operation, aerial vehicle, field call, etc. It can remote control equipments on
land, water and air, such as remote control lights, sirens, locks, motors,
fans, winches, blinds, linear actuators, doors, windows, electric solenoid
valves, security alarm, business signs and various devices. Wireless control, easy
to install. Waterproof:
The receiver has waterproof case and waterproof connector, it can be installed
outdoors. AC Power
Output: It can control AC equipment with voltage 12V / 24V AC. With wired control terminals:
You can connect sensors, limit switches,
manual switches or external devices to control the receiver. You can
turn on/ off the receiver with transmitter (remote control) from any place
within a reliable distance. Wireless RF
signal can pass through walls, floors, doors or windows. With
reverse power protection and over current protection. Reliable
control: The receiver only works with the transmitter which use same code. One/several
transmitters can control one/several receivers simultaneously. You can use
two or more units in the same place. Receiver Parameters: Model No.: S2X-AC12-ANT3 Power Supply
(Operating Voltage): AC12~24V Output: AC12~24V Working Frequency: 433MHz Channel: 2 CH Control Modes: Self-locking, Momentary, Interlocking Static Current: ≤6mA Maximum Working
Current: 10A / each channel
PCB size: 88 x 80 x 18 mm (3.5 x 3.1 x 0.7 inches)
Case size: 115 x 90 x 55 mm (4.5 x 3.6 x 2.2 inches)
Work with Fixed code transmitters or Learning code transmitters. Matching Transmitters: The
receiver can work with different transmitters, such as model C-2 / C-3(100M),
CWB-2 / CWB-3 (50M, waterproof), CP-2 (500M), or CB-2 / CB-3 (1000M) etc. When you
set the receiver in toggle or momentary mode, it should work with two
buttons transmitter, such as model C-2 (100M), CWB-2
(50M, waterproof), CP-2 (500M), or CB-2 (1000M) etc. When you set the receiver
in latched mode, it should work with three buttons
transmitter, such as model C-3 (100M), CWB-3 (50M, waterproof), or CB-3 (1000M)
etc. Working
Range: With a transmitter (such as CWB-2) to form a complete
set, the maximum working distance can reach 50Min
an open ground. The maximum working
distance is a theoretical data, it shall be operated in an open ground, no
barriers, no any interference. But in the practice, it will be hindered by
trees, walls or other constructions, and will be interfered by other wireless
signals. Therefore, the actual distance may not reach this
maximum working distance. If you
want to have a further working range, you can install an external antenna to
the receiver, and you also can use a powerful
transmitter, such as CB series transmitters. Usage (with
the transmitter CWB-2): The receiver can be used to control AC12~24V equipments. Wiring: If you want to control an AC12V lamp, do as following: 1) Connect the live wire of AC power supply to terminal “L / +” of INPUT,
and connect the neutral wire of AC power supply to terminal “N / -” of INPUT. 2) Connect one side of AC lamp to terminal "L / +" of OUTPUT, and connect another side of AC lamp to terminal
"N / -" of OUTPUT. Setting different control modes: Setting
different control modes: (We have set the receiver in Self-locking mode before
delivery, if you want to use other modes, do as following operation.) Setting
control mode Self-locking: Only connect Jumper-2. Control
mode Self-locking (with transmitter CWB-2): Press -> On; Press again -> Off. Press button
A of the transmitter: Terminals “OUT1” outputs AC power, the lamp 1 is on. Press button
A again: Terminals “OUT1” stops outputting, the lamp 1 is off. Press button
B of the transmitter: Terminals “OUT2” outputs AC power, the lamp 2 is on. Press button
B again: Terminals “OUT2” stops outputting, the lamp 2 is off. Setting
control mode Momentary: Only connect Jumper-1. Control
mode Momentary (with transmitter
CWB-2): Press and hold -> On; Release -> Off. Press and
hold button A of the transmitter: Terminals “OUT1” outputs AC power, the lamp 1
is on. Release
button A of the transmitter: Terminals “OUT1” stops outputting, the lamp 1 is
off. Press and
hold button B of the transmitter: Terminals “OUT2” outputs AC power, the lamp 2
is on. Release
button B of the transmitter: Terminals “OUT2” stops outputting, the lamp 2 is
off. Setting
control mode Interlocking: Do not connect Jumper-1 and Jumper-2. Control
mode Interlocking (with transmitter CWB-3): Press -> On, Press another button
-> Off. Press button
B of the transmitter: Terminals “OUT1” outputs AC power, the lamp 1 is on. Press button
C of the transmitter: Terminals “OUT2” outputs AC power, the lamp 2 is on. Terminals “OUT1” stops
outputting, the lamp 1 is off. Press button
A of the transmitter: Terminals “OUT2” stops outputting, the lamp 2 is off. Wired control terminals: The
receiver has manual control terminals, you can connect external devices,
sensors, or manual switches to control the receiver. 1) Signal
input: You can
connect external devices (with low level output signal) to manual terminals 1
(Signal +), terminal 2 (Signal +) and terminal 3 (Signal -) , then the external
device’s output signal can control the receiver. When the
external device outputs low level signal to manual terminal 1 and terminal 3, turns on the
relay 1. Terminals “OUT1” outputs AC power, the lamp 1 is on. When the external device stops to output signal, turns off
the relay 1. Terminals “OUT1” stops outputting, the lamp 1 is off. When the
external device outputs low level signal to manual terminal 2 and terminal 3, turns on the
relay 2. Terminals “OUT2” outputs AC power, the lamp 2 is on. When the external device stops to output signal, turns off
the relay 2. Terminals “OUT2” stops outputting, the lamp 2 is off. 2) The manual switches: You can
connect manual switches to manual terminals 1, 2 and 3, then you can use
manual switches to control the receiver. When connect terminals
1 and 3, turns on the relay 1. Terminals “OUT1”
outputs AC power, the lamp 1 is on. And when
disconnect terminals 1 and 3, turns off the relay 1. Terminals “OUT1” stops
outputting, the lamp 1 is off. When connect terminals
2 and 3, turns on the relay 2.Terminals
“OUT2” outputs AC power, the lamp 2 is on. And when
disconnect terminals 2 and 3,turns off the
relay 2. Terminals “OUT2” stops outputting, the lamp 2 is off.
