Matching Transmitters:
The receiver can work with different transmitters, such as model C-2 / C-3(100M), CWB-2 / CWB-3 (50M, waterproof), CP-2 (500M), or CB-2 / CB-3 (1000M) etc.
When you set the receiver in toggle or momentary mode, it should work with two buttons transmitter, such as model C-2 (100M), CWB-2 (50M, waterproof), CP-2 (500M), or CB-2 (1000M) etc. When you set the receiver in latched mode, it should work with three buttons transmitter, such as model C-3 (100M), CWB-3 (50M, waterproof), or CB-3 (1000M) etc.
Working Range:
With a transmitter (such as CWB-2) to form a complete set, the maximum working distance can reach 50M in an open ground.
The maximum working distance is a theoretical data, it shall be operated in an open ground, no barriers, no any interference. But in the practice, it will be hindered by trees, walls or other constructions, and will be interfered by other wireless signals. Therefore, the actual distance may not reach this maximum working distance.
If you want to have a further working range, you can install an external antenna to the receiver, and you also can use a powerful transmitter, such as CB series transmitters.
Usage (with the transmitter CWB-2):
The receiver can be used to control AC12~24V equipments.
Wiring:
If you want to control an AC12V lamp, do as following:
1) Connect the live wire of AC power supply to terminal “L / +” of INPUT, and connect the neutral wire of AC power supply to terminal “N / -” of INPUT.
2) Connect one side of AC lamp to terminal "L / +" of OUTPUT, and connect another side of AC lamp to terminal "N / -" of OUTPUT.
Setting different control modes:
Setting different control modes: (We have set the receiver in Self-locking mode before delivery, if you want to use other modes, do as following operation.)
Setting control mode Self-locking: Only connect Jumper-2.
Control mode Self-locking (with transmitter CWB-2): Press -> On; Press again -> Off.
Press button A of the transmitter: Terminals “OUT1” outputs AC power, the lamp 1 is on.
Press button A again: Terminals “OUT1” stops outputting, the lamp 1 is off.
Press button B of the transmitter: Terminals “OUT2” outputs AC power, the lamp 2 is on.
Press button B again: Terminals “OUT2” stops outputting, the lamp 2 is off.
Setting control mode Momentary: Only connect Jumper-1.
Control mode Momentary (with transmitter CWB-2): Press and hold -> On; Release -> Off.
Press and hold button A of the transmitter: Terminals “OUT1” outputs AC power, the lamp 1 is on.
Release button A of the transmitter: Terminals “OUT1” stops outputting, the lamp 1 is off.
Press and hold button B of the transmitter: Terminals “OUT2” outputs AC power, the lamp 2 is on.
Release button B of the transmitter: Terminals “OUT2” stops outputting, the lamp 2 is off.
Setting control mode Interlocking: Do not connect Jumper-1 and Jumper-2.
Control mode Interlocking (with transmitter CWB-3): Press -> On, Press another button -> Off.
Press button B of the transmitter: Terminals “OUT1” outputs AC power, the lamp 1 is on.
Press button C of the transmitter: Terminals “OUT2” outputs AC power, the lamp 2 is on.
Terminals “OUT1” stops outputting, the lamp 1 is off.
Press button A of the transmitter: Terminals “OUT2” stops outputting, the lamp 2 is off.
Wired control terminals:
The receiver has manual control terminals, you can connect external devices, sensors, or manual switches to control the receiver.
1) Signal input:
You can connect external devices (with low level output signal) to manual terminals 1 (Signal +), terminal 2 (Signal +) and terminal 3 (Signal -) , then the external device’s output signal can control the receiver.
When the external device outputs low level signal to manual terminal 1 and terminal 3, turns on the relay 1. Terminals “OUT1” outputs AC power, the lamp 1 is on.
When the external device stops to output signal, turns off the relay 1. Terminals “OUT1” stops outputting, the lamp 1 is off.
When the external device outputs low level signal to manual terminal 2 and terminal 3, turns on the relay 2. Terminals “OUT2” outputs AC power, the lamp 2 is on.
When the external device stops to output signal, turns off the relay 2. Terminals “OUT2” stops outputting, the lamp 2 is off.
2) The manual switches:
You can connect manual switches to manual terminals 1, 2 and 3, then you can use manual switches to control the receiver.
When connect terminals 1 and 3, turns on the relay 1. Terminals “OUT1” outputs AC power, the lamp 1 is on.
And when disconnect terminals 1 and 3, turns off the relay 1. Terminals “OUT1” stops outputting, the lamp 1 is off.
When connect terminals 2 and 3, turns on the relay 2. Terminals “OUT2” outputs AC power, the lamp 2 is on.
And when disconnect terminals 2 and 3, turns off the relay 2. Terminals “OUT2” stops outputting, the lamp 2 is off.
