Hi, I'm Tom. Welcome to our shop,
Carymart offers you the premium rf remote control equipment.
We suggest you reading our FAQs before making your decision.
If you have any other question, please contact us.
We will reply you as soon as possible.
Application:
This receiver is an electric device with 15 dry relay outputs, it and the
transmitter form a wireless remote-control system. This system may be used
in all types of industry automation, agriculture, business, home, factory,
house, farm, garage, vehicle, ship, aerial vehicle, etc. It can remote
control different AC or DC equipment on land, water, and air, such as
lights, doors, windows, lamps, sockets, locks, sirens, outlets, heaters,
motors, fans, winches, curtains, blinds, linear actuators, electric solenoid
valves, and security alarm systems. The applications are endless.
Feature:
Wireless control, easy to install.
Two operating voltage versions, DC 12V, 24V optional.
Relay Output: This receiver is dry relay output, it can be used to operate
both DC and AC equipments. The output terminals are NO / NC (normally open /
normally closed), which serves as a switch. That means you should also
connect a separate power supply to equipments.
Each channel can work at maximum current 10A.
With external telescopic antenna, the receiver has a farther working range.
The transmitter / remote can control the receiver from any place within a
reliable working distance.
The wireless RF signal from the transmitter can pass through walls, floors,
doors or windows, but it will lose some operating range.
The receiver has reverse voltage protection and overcurrent protection.
The receiver can only be triggered by paired transmitters.
One or more transmitters / remotes can control one or several receivers
simultaneously.
Two or more receivers may be used in the same area.
Receiver Parameters:
Model: S15C-DC-ANT3
Operating Voltage: 12±1VDC (model S15C-DC12), or 24±2VDC (model S15C-DC24),
the operating voltage must be specified when ordering.
Working Frequency: 433.92MHz
Static Current: ≤6mA
Channel: 15 CH
Output Type: Relay Output (With Normally Open and Normally Closed Terminals)
Maximum Load Voltage of Relay: 240VAC or 28VDC
Maximum Load Current of Relay: 10A / each channel
Suitable Wires for Connecting Terminals: 24-18 AWG
5 Selectable Working Modes: Self-locking, Momentary, Interlocking¸ Mixed
modes
Operating Temperature: -20 ° C to +70 ° C
PCB size: 120 x 73 x 17 mm (4.7 x 2.9 x 0.7 inches)
Case Size: 126 x 79 x 30 mm (5.0 x 3.1 x 1.2 inches)
Transmitter Parameters:
Model: 0021015 (CV-15)
Channel/Button: 15
Button Symbol: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15
Operating Voltage: 12V (1 x 23A -12V battery, can be used for 12 months)
Operating Current: 15mA
Operating Frequency: 433Mhz
Encoding Chip: PT2262 / PT2264 / SC2262
Encoding Type: Fixed code by soldering, up to 6561 codes
Transmitting Distance: 500m / 1500ft (theoretically)
Modulation Mode: ASK
Operating Temperature: -20 ° C to +70 ° C
Unit Size: 118 x 50 x 17 mm
Matching Transmitters:
The receiver can work with different transmitters, such as model
CV-15(500M),
C-1(100M), or
CB-1(1000M) etc.
Note 1: If you use the transmitter CV-15 to work with this receiver, because
the transmitter CV-15 has total 15 buttons, so that each button will trigger
a channel of this receiver.
Note 2: If you use the transmitters C-1 or CB-1 to work with this receiver,
because these transmitters have only a button, so that each transmitter will
trigger a channel of this receiver.
Working Range:
The receiver and the transmitter (such as CV-15) form a complete kit, the
maximum working distance may reach 1500 feet or 500 meters in an open area.
The maximum working distance is theoretical data, it shall be operated in an
open ground, no barriers, no interference. But in practice, it will be
hindered by trees, walls or other constructions, and will be interfered by
other wireless signals. Therefore, the actual working distance may not reach
this maximum distance.
Usage:
The receiver can be used to control both DC 0~28V and AC 110~240V
equipments.
Notice: The receiver is relay output, not DC/AC power output. Initial state
of relay output terminals: Terminals NO and COM are Normally Open;
Terminals NC and COM are Normally Closed.
Wiring:
1) If you want to control a DC 12V lamp, do as following:
1.1 Connect the DC power supply to the V1 and V2 terminals (Both V1
and V2 terminals can be connected to the positive and negative poles of
the DC power supply), or plug the DC power supply into the power socket on
the receiver.
1.2 Connect terminal NO to the positive pole of DC power supply, connect
terminal COM to the positive pole of DC lamp, and connect the negative
pole of DC lamp to the negative pole of DC power supply.
2) If you want to control an AC 120V lamp, do as following:
2.1 Connect the DC power supply to the V1 and V2 terminals (Both V1
and V2 terminals can be connected to the positive and negative poles of
the DC power supply), or plug the DC power supply into the power socket on
the receiver.
2.2 Connect terminal NO to the live wire of AC power supply, connect
terminal COM to one side of AC lamp, and connect another side of AC lamp
to the neutral wire of AC power supply.
Setting different control modes:
The receiver will be set in Self-locking mode before leaving the factory, if
you want to use another mode, please follow the following steps.
Note: Need to delete all transmitters codes stored in
the receiver before changing the working mode.
1) Setting Self-locking mode: When the receiver is in the learning status,
press the button 1 on the transmitter.
The operation of Self-locking mode with the transmitter CV-15:
Press the button 1 on the transmitter: The relay 1 in the receiver is
activated, and the connected lamp 1 is turned on.
Press the button 1 again: The relay 1 is deactivated, and the connected lamp
1 is turned off.
…...
Press the button 15 on the transmitter: The relay 15 in the receiver is
activated, and the connected lamp 15 is turned on.
Press the button 15 again: The relay 15 is deactivated, and the connected
lamp 15 is turned off.
2) Setting Momentary mode: When the receiver is in the learning status,
press the button 2 on the transmitter.
The operation of Momentary mode with the transmitter CV-15:
Press and hold the button 1 on the transmitter: The relay 1 in the receiver
is activated, and the connected lamp 1 is turned on.
Release the button 1: The relay 1 is deactivated, and the connected lamp 1
is turned off.
…...
Press and hold the button 15 on the transmitter: The relay 15 in the
receiver is activated, and the connected lamp 15 is turned on.
Release the button 15: The relay 15 is deactivated, and the connected lamp
15 is turned off.
3) Setting Interlocking mode: When the receiver is in the learning status,
press the button 3 on the transmitter.
The operation of Interlocking mode with the transmitter CV-15:
Press the button 1 on the transmitter: The relay 1 in the receiver is
activated, and the connected lamp 1 is turned on. Other 14 relays are
deactivated and other 14 connected lamps are turned off.
…...
Press the button 15 on the transmitter: The relay 15 in the receiver is
activated, and the connected lamp 15 is turned on. Other 14 relays are
deactivated and other 14 connected lamps are turned off.
4) Setting Self-locking (Channel 1~8) + Momentary (Channel 9~15) mode: When
the receiver is in the learning status, press the button 4 on the
transmitter.
5) Setting Self-locking (Channel 1) + Momentary (Channel 2~15) mode: When
the receiver is in the learning status, press the button 5 on the
transmitter.
How to pair the transmitter to the receiver:
Notice: We have paired the transmitter to the receiver before leaving the
factory. If you want to pair more remote controls, please follow the
following steps.
1) Press the learning button in the receiver once, and the signal LED on the
receiver turns on first and then goes off, this indicates that the receiver
enters the learning status.
2) Press the corresponding button on the transmitter according to the
working mode you need, if signal LED flashes once slowly, this indicates
that the pairing is successful.
3) The receiver can learn about 30 transmitters with different codes.
How to delete all transmitters codes stored in the receiver:
We have paired the transmitter to the receiver, if you don’t want the
receiver to work with the transmitter, you can delete all transmitters codes
stored in the receiver.
Operation: Press and hold the learning button of receiver for 8-9 seconds,
until the signal LED on the receiver turns off, then release the learning
button, this indicates that all stored codes have been deleted successfully.
Package Include:
1 x Receiver: S15C-DC-ANT3
1 x Transmitter: CV-15
1 x User manual
